Home
> >

Cannondale CAAD10 (2015)

I bought the Caad10 frame as replacement for my old crashed frame in july 2015. First build it up with the DA 7700 group set from the crashed bike and used as winter training bike. After two years of riding upgrade it to Sram R3d and new Mavic R-Sys wheels

Frame:
CAAD10

Fork/Headset:
CAAD10/ Canndondale/ Tange/ super six 4.5 mm headset top cap with 10 spacer mm below the stem

Crankset/Bottom Bracket:
Quark dzero sram red style (110mm bcd), Kogel BB30 ceramic road version

Pedals:
Dura Ace 9100

Drivetrain/Cog/Chainring/Chain:
Edco monoblock, 11-28 cassette, Extralite OctaRamp mc 36-52

Derailleurs/Shifters:
Sram Red

Handlebars/Stem:
Easton E100 (420mm) Extralite HyperStem Stealth (110mm -12°) Extralite Expander UltraStar 3 + Hypercap top cap

Saddle/Seatpost:
Canndondale C2 Prologo Scratch 2 Nack

Brakes:
Sram Red

Front Wheel/Hub/Tire:
AC 350 (28h, DT Aerolite, radial laced) / Tune Mig 45/ Conti Attac 2

Rear Wheel/Hub/Tire:
AC 350 (32h, DT Aerolite, 3 cross laced) / Tune Mag 170/ Conti Force 2

Accessories:
K-Edge Garmin mount + gopro mount for the lezyne light, Garmin Edge 520

More Info:
overall weight including garmin is now slightly below 6.8 kg

Bike History

Click a link below to see past stages of this bike.

  1. DA7700
  2. Sram Red
  3. Riding 2 Power and getting more aero
  4. -12°
  5. UCIllegal

Current Stage Info:

Spare/ winter AC wheelset @ 1.2kg with lighter tires, complete bike @ 6.7 kg

Added by pnk. Last updated 12 days ago.

7 Comments

pellesplendida

pellesplendida says:

Shimano cassette (160 euros) or KMC chain (70 euros) could be the problem. Now I cry like a child
Thank you so much ;-)

Posted 6 months ago

pellesplendida

pellesplendida says:

Hi, I installed the crank Red Quarq Dzero, I'm worried and desperate. The crank is perfectly centered between NDS and DS sides but the chain line does not seem to be correct ... 36-28, 36-25, 36-25 work very badly. The photos of your Caad show you have the same crank Sram Red Dzero quarq dzero BB30 / BB386. I installed chainring sram red etap, chain kmc SL DLC 11v and cassette 11-28 Dura Ace 9100 ..... maybe that's the problem? With Sram Force 10v I have always used KMC chains and cassette Shimano never problems.

Posted 6 months ago

pnk

pnk says:

Sorry to hear that its not working jet for you :( With the Extralite chainrings and the sram red casette I use there is no problem with the chainline in the 36:28-25 gears. I even can use 52:28-25 without any chainrubbing. Before I installed the quark crank I had a standard sram red 22 crank installed (130mm bcd). The only thing I adjusted on the gearing when upgrading to the quark was moving the front derailleur a littel bit down and retentioning the FD cabel.
Since we have different chainrings, chains and casettes all of these could be the cause for your problems. If possible I would first check a different cassette and then if possible different chainrings as well. However since these are the original sram chaning rings they should not be the cause of your problems...

Posted 6 months ago

pellesplendida

pellesplendida says:

you have explained very well. thank you so much

Posted 6 months ago

pnk

pnk says:

You're welcome! and don not forgett to post your caad here when your build ist done :)

Posted 6 months ago

pellesplendida

pellesplendida says:

congratulations for the bike.
A question, the crankset quarq dzero have you installed with 13 mm spacer in the drive side and 4.84 mm spacer & preload adjster in the no drive side? You can send me a photo?, I also have to mount it on my caad 10.

Posted 7 months ago

pnk

pnk says:

First I only installed the 13mm spacer on the drive and the preload adjuster on the non drive side. This setup worked well for the 500k I did with it. However the preload adjuster had to span a relatively wide distance to make the crank-set/ axel free of any side movement. Thus I decided to additionally add a wave washer between the left-/ non drive side crank arm and the preoload adjuster. For this I used one of the wave washers which were inlcuded in the set of spacer for EVO 386 install of the quark. With this imo better setup I've done another 500k and it feels super stiff and secure in place.

HTH and if need I will add a picture as soon as I return to the bike!

Posted 6 months ago