Home
Forums >

Posts by AKfromGC

Post Preview Topic
November 5, 2014 02:08 AM in General Discussion

If not done up too tight, then yeah you can get them apart without a puller. But if they're cranked up tight (no pun intended). With no choice yeah..... There would be lots of ...

Seized crank arm
November 5, 2014 01:58 AM in General Discussion

What a collection of memes you have at your disposal. JIS ISO into the search bar and the first thing up is....... Sheldon Brown. http://sheldonbrown.com/bbtaper.html

Bottom Bracket for Dura Ace 7600 Cranks
November 4, 2014 05:59 AM in General Discussion

I would get two, three if I could get a good deal, cheap arse fixies. Retrospec or something like that. Riding with friends is more fun. Basic foot retention. Then use the chang...

make a bike with $1200
November 3, 2014 09:48 PM in General Discussion

I love when there is an open ended thread when you go to bed. And in the morning there was a visit from Scrodzilla during the night. Leaving behind a post of wisdom. Heavily coa...

Track crank on a Single Speed Cyclocross?
November 3, 2014 11:15 AM in General Discussion

??? The cranks on the bike are a single speed crank set. Look at the photo. Road cranks are as equally as stiff as track cranks. That is comparable quality cranks are. Unless...

Track crank on a Single Speed Cyclocross?
November 2, 2014 10:15 AM in General Discussion

You link needs a little editing to work properly. Cute idea, but I can't see it taking off. Will I carry a little stand or just lean the bike against something.' I could be...

STAND4CURE
November 2, 2014 09:38 AM in General Discussion

Even if your cranks aren't on your bike you may struggle pulling the arms off the spindle without a crank arm puller. A big yellow screwdriver, wedges, hammers and the like will...

Seized crank arm
October 28, 2014 06:04 AM in General Discussion

http://www.weinmanntek.com/Products/RACE/DP18.htm http://hplusson.com/products/archetype There you go. Too bad velocity rims have gone down hill. They should have kept the f...

Hplusson wheels??
October 22, 2014 07:43 PM in General Discussion

The problem with bull horns is the lack of variation in hand positions. Hands are always at one level. Lower the stem. Good for going hard. But not so much for just cruising a...

Spacers...
October 22, 2014 07:25 PM in General Discussion

^^ as above. Slam it. Find out how it feels. You're a big boy,(maybe a girl). You don't need a forum to tell you how to experiment with your bike set up. Just don't cut the st...

Spacers...
October 22, 2014 07:04 AM in General Discussion

One of the craziest things I had done (multiple times) would have been in my late teens, early 20s. I had a road bike and I would slip stream behind buses and trucks. A real buz...

crazy experiences when riding your bike.
October 18, 2014 01:14 AM in General Discussion

Flip a coin. Roll a dice. Shipping shouldn't take weeks. What looks best for you. Both are race proven crank sets. Just check if they come with a bottom bracket. Generally...

Sugino 75 vs. dura Ace 7600?
October 13, 2014 02:42 AM in General Discussion

You get it from the box that the headset comes in, (buy a new one). If you're lucky your lbs may have parts. Otherwise buy complete. And make sure not to lose any parts. The m...

Problem with my fork
October 12, 2014 11:49 AM in General Discussion

I bought a couple of knogs back in May. 1 LED blinder on the front and a wearable boomer for the rear. The blinder is USB chargeable and has been good so far. I have 26mm bars...

USB chargeable lights
October 8, 2014 02:00 AM in General Discussion

http://www.retro-gression.com/product/h-son-archetype-formula-track-wheelset Just buy these ones and be done with it. Two things, you get a new solid set of wheels and you also...

I would like as much input as possible on this wheel set from city grounds
October 7, 2014 11:50 PM in General Discussion

http://www.retro-gression.com/category/components-wheels-rims-hubs-spokes This shop has lots of good stuff. The fixed/free hub gives the option of both on the one wheel.

I would like as much input as possible on this wheel set from city grounds
October 7, 2014 11:41 PM in General Discussion

Cartridge bearings are the type of bearing. Like skateboard bearings. They are a single unit. Then you can get different types. Open, dust cover, sealed. And then different qual...

I would like as much input as possible on this wheel set from city grounds
October 7, 2014 11:34 PM in General Discussion

Ridingfixed. Yeah you can. I have at the moment. The larger fixed thread is a right hand thread the same as a freewheel thread. The smaller left hand thread for the lock ring do...

I would like as much input as possible on this wheel set from city grounds
October 7, 2014 11:27 PM in General Discussion

MICHE PISTARD TRACK BIKE FIXED GEAR WHEELSET TUBULAR It says it right there in the discription what they are. If they are for street use then get sealed bearing hubs like the...

I would like as much input as possible on this wheel set from city grounds
October 7, 2014 07:37 PM in General Discussion

They look good. You'd have to listen to Rage Against the Machine while riding one.

Anyone ridden a Bombtrack Script 2014?
October 7, 2014 11:46 AM in General Discussion

Ha ha. I'm sure someone on here once said 'If it feels too spinny, learn to spin.'

?perfect gear ratio?
October 7, 2014 09:43 AM in General Discussion

Where? It's a big country. I believe half of as new price is a good start. There are other factors of course. How the 2nd hand market is going and availability. Check out gumt...

Cinelli Mash 2011 selling price
October 6, 2014 11:09 AM in General Discussion

It sounds insignificant compared to the previous posts. 104km. A group ride in a local cycling festival. I was the only single speed rider too.

Longest ride you ever done before?
October 5, 2014 11:00 AM in General Discussion

Scrod. And when you do have to stoop down and use gear ratios. I bet you use a free wheel too. That way when you go up hills, if you don't want to pedal, you don't have to.

?perfect gear ratio?
October 5, 2014 10:55 AM in General Discussion

Take it to a metal frabrication workshop. Preferably one that builds race cars/bikes. They can weld and understand your requirements. I took my old alloy GT power series cranks ...

Restoring worn aluminum dropouts?