I was looking for a replacement frame because my custom steel frame starts to rust more and more. Getting it painted without a phosphate rust protection on the inside feels like a bad investment and nobody offers a phosphate coating for bikes.
Frame:
Standert Pfadfinder 52cm Midnight Marauder (RAL 790-6) steel Columbus tubing
Fork/Headset:
Enve all road IN-Route carbon, axle to crown 380mm, fork offset 47mm / upper ans lower Hope EC44/40 with Ceramicspeed OHD SLT 52x40x7mm 45°/45° bearing / custom short compression ring and Deda 56mm headset topcover
Crankset/Bottom Bracket:
Garbaruk road crank 160mm with 130mm DUB spindle and 110BCD spider / BBinfinite T47 extrnal DUB with 30x24x7mm bearings
Pedals:
Shimano Dura-Ace PD-R9100 or XTR PD-M9100 with Meti Ti Axle
Drivetrain/Cog/Chainring/Chain:
Shimano 1x12 / Shimano Dura-Ace CS-R9100 11-34 / BCD110 spider with Garabaruk round chainrings 40/46/52T / Shimano Dura-Ace CN-M9100 chain
Derailleurs/Shifters:
Shimano Ultegra Di2 RD-R8150 / Shimano Ultegra ST-R8170 and custom BL-R8170
Saddle/Seatpost:
Björn Probka leo kork 143 mm / Thomson titanium 27.2mm / Thomson Seatclamp
Brakes:
Trickstuff C22 / Trickstuff dächle 140mm / Intend skinny 160mm with Galfer center lock adapters
Front Wheel/Hub/Tire:
690g Nextie Carbon 50mm NXT50GX ERD541mm 425g 50x29x22mm laced with 24x 260mm Sapim CX-Ray to DT-SWISS 350 with black Sapim polyax 12mm brass nippels / 28mm pink corsa pro
Rear Wheel/Hub/Tire:
820g Nextie Carbon 50mm NXT50GX ERD541mm 425g 50x29x22mm laced with 28 Sapim CX-Ray (DS256mm, NDS258mm) to DT-SWISS 350 with black Sapim polyax 12mm brass nippels / 28mm pink corsa pro
Accessories:
King Cage titanium bottlecages / pro-bolt titanium bolts / Silca 3d printed direct mount UDH / Meti titanium pedalaxles, Carbonworks mastermount, Williams Racing Products zero drag dt ratchet
More Info:
Xkg total incl. pedals, cages and garminmount
Bike History
Click a link below to see past stages of this bike.
Added by ianiscaratti. Last updated 11 days ago.
23 Comments
Clean, Cleaner, Cleanest!
Amazing work with the cable routing through one of the most beautiful stems (except X2 or G2, even if I am not sure if I want to go back to a 2 bolt stem).
Posted 4 months ago
Oh yeah this gon' be good
Posted 5 months ago
did you find one? I was initialy looking for the Stichsäge CX frameset but they don't do it anymore.
Posted 4 months ago
oh you got it!
Posted 6 months ago
8.6kg with pedals, cages and garminmount. 1kg lighter than my steel Aerocross but also 1kg heavier than my alloy Allez.
Posted 4 months ago
the kolb is starting to rust ? wth
Posted 7 months ago
it had cavity spray from the beginning and rusted a lot after only 8 month. I spray a complete bottle in the frame every 12 month. heat it with a heat gun and turn it to coat every angle
Posted 7 months ago
I'm ready
Posted 9 months ago
new update becaus I could not find any ICR stem that looks good so this will be very clean with SZ44 upper headset because EC44 upper headset look weird.
Posted 5 months ago
Photos
FixedMaksaks says:
Baller saddle
Posted about 1 month ago
ianiscaratti says:
Thanks
Posted 27 days ago